Resepmpasi
Nutrition

Anita Herbert’s Smith Machine Workout Targets Back and Shoulders

Written Oct 27, 2026 Audience 518 Author vkim

Anita Herbert pairs six Smith machine movements into three supersets, with rep targets and form cues for a focused back and shoulder session.

Anita Herbert’s Smith Machine Workout Targets Back and Shoulders

A machine based routine with a practical caveat

Anita Herbert’s upper-body routine makes a case for the Smith machine as a useful tool for training the back and shoulders, while also showing why a machine’s label doesn’t tell you exactly how a lift will feel. The IFBB Pro and coach shared six movements arranged in three supersets, pairing presses with rows and pull-ups. That structure gives the session a clear rhythm: a push is followed by a pull, then the next pairing changes the emphasis. The fixed bar path can make the machine feel different from free weights, Herbert says, so the load may surprise lifters accustomed to a barbell.

That difference matters when you’re choosing a starting weight. A guided bar can reduce the balancing demands of a movement, but it still has its own resistance and feel. If you’re used to judging a lift by what you can press or row with a free bar, the number on the Smith machine may not be a direct comparison. The useful measure is how well you can control the movement through the intended range.

Herbert posted the session on Instagram for her “Fit Queen Army” followers, inviting them to save it for an upper-body workout. For people who find free weights difficult to balance, the machine offers another way to train with resistance while keeping the bar on a guided path. That can make it easier to focus on repeating a movement, though a fixed track also sets limits on how the bar travels. A machine should suit the exercise and the lifter; the presence of rails alone doesn’t make every setup comfortable.

“FitQueen” Anita Herbert demonstrating her Legs and Glutes Workout

Less Equipment, More Muscle With Anita Herbert&#03...

The “FitQueen” showed how to get the most from each machine

Read article

The workout: three supersets

Complete the listed rounds in sequence. Herbert’s routine alternates shoulder pressing with back work, then finishes with two more pulling variations. The round counts vary: the first and third pairings call for three rounds, while the second calls for two. That makes the workout’s structure straightforward to follow, but the rep targets still leave room to adjust the load to your control and experience.

In a superset, you move between the two listed exercises before repeating the pair. The point here is to alternate different movement patterns, rather than to treat the six exercises as one long block of presses followed by one long block of pulls. Take enough time to set up each movement safely and keep the repetitions deliberate.

Superset 1 — 3 rounds

  1. Shoulder press: 8 to 10 reps
  2. Inverted underhand-grip row: 10 reps

The opening pair puts a press beside a row, so the session starts with work for both the shoulders and back. The rep targets are close enough to make the transition easy to remember, but they don’t require you to use the same load or effort level on each exercise.

Superset 2 — 2 rounds

  1. Wide-grip paused eccentric pull-up: 6 to 8 reps
  2. Single-arm shoulder press: 8 reps per arm

The second pair changes the pulling movement and switches the press to one arm at a time. That creates a different coordination demand, especially if you’re still learning how to brace while pressing independently. The two rounds also make this the shortest superset by volume, based on the listed prescription.

Superset 3 — 3 rounds

  1. Single-arm row: 8 to 10 reps per arm
  2. Upright row: 10 to 12 reps per arm

The final pair keeps the back involved and closes with an upright row. Since both exercises call for work on each side, allow for the time needed to complete the reps evenly. A rushed changeover can make it harder to keep the same posture and control from one side to the other.

Why the pairings work

The first pairing combines a shoulder press, which emphasizes the front deltoids and also recruits the upper back, triceps and core, with an underhand inverted row for the mid-back, lats and rear delts. The alternation gives the shoulders and back consecutive work without repeating the same movement pattern. That’s a sensible way to organize an upper-body session: one movement asks you to press, the next asks you to pull, and the shift can help keep the workout from becoming repetitive.

In the second round, the wide-grip pull-up variation shifts attention to the lats, rhomboids and upper trapezius. Herbert’s version starts from a seated position, with the feet available for support. A brief pause at the top increases time under tension; keep the motion controlled and avoid shrugging. The single-arm press that follows adds another shoulder stimulus and lets each side work independently. If one side feels less coordinated, the unilateral setup makes that difference easier to notice, though the routine doesn’t prescribe a separate correction for it.

The final pairing opens with a single-arm row for the lats, traps and rear delts. Brace the core, keep the elbow close to the body and focus on driving the movement through the back. The upright row closes the session, challenging the shoulders and upper back while also involving the triceps and grip. Taken together, the sequence gives the upper body repeated pulling work, with shoulder pressing appearing in the first two pairings and a different shoulder-focused movement at the end.

Expect the bar to feel different

A guided bar path can reduce the balance demands of a lift, but it doesn’t guarantee that a given weight will feel lighter. “It can feel heavier than free weights, especially for upper body exercises because Smith machines have different bar weights, counterbalance systems and resistance,” Herbert explained in the comments on her post. “The fixed bar path also changed how the movement feels, compared to free weights.”

Her explanation points to a practical issue with machine training: the equipment itself shapes the exercise. Smith machines can differ in bar weight, counterbalance and resistance, and those details affect how a load feels in use. A number on one machine may not translate neatly to another, or to a free bar. Here's the thing: the rep target is a guide, not evidence that every lifter should use the same load.

What the routine means for your training

That’s the practical point of the routine: use the listed reps as a framework, then account for how your specific machine moves. This is more significant than it looks. A guided track may simplify balance, but the machine still asks you to find a comfortable position and control the bar through each repetition. Start with a load that lets you do that; the source gives rep ranges, but it doesn’t specify weights, rest periods or a progression plan.

If you're working in this space, pay attention to the setup as well as the exercise name. Seat position, grip and the machine’s path can all affect how a movement feels, so a routine shared online may need adjustment to fit the equipment in front of you. The workout’s value lies in its clear push-and-pull structure and accessible rep targets. The machine isn’t a shortcut around technique. A useful framework, with room for judgment.

That said, Herbert’s post is best read as a session template rather than a complete training program: it offers movements and repetitions, but doesn’t explain how often to repeat the workout or how to progress it. What this means for you is simple: use the sequence as a starting point, and judge each movement by your control and comfort on the machine you have. To follow Anita Herbert on Instagram, click here.

Source: vkim · www.muscleandfitness.com

Discussion

Sign in to join the discussion.